KDTRADERSELECTRONICSHYDERABAD 5860b1ff68346f1df84141e3 False 122 54
OK
Updates

No results found!

How to Use Rotary Evaporator or Rotavapor
General rules for usage of rotary evaporators

1. The solvent collection flask of the unit should always be emptied prior use to prevent accidentally mixing of incompatible chemicals. SAFETY FIRST! 

2. The flask with the solution is placed on the rotary evaporator. The use of a bump trap prevents the solution from accidentally splashing into the condenser (and being contaminated). It is highly advisable to start with a clean bump bulb in case something bumps over after all! This would allow the experimenter to recover the solution or solid.

  


3. A metal or Keck clip is used to secure the flask and the bump trap. The green one shown below fits 24/40 ground glass joints. Similar blue clips fit 19/22 joints and the yellow ones fit 14/20 joints, which will most likely used in the lab. If you break the bump trap, you will have to pay for it!

4. The dial on the motor is used for speed control of the flask rotation. A typical rotavap uses a variable speed sparkless induction motor that spins at 0-220 rpm and provides high constant torque. A good setting here is 7-8. 

5. The aspirator vacuum is turned on. On most models, the vacuum on/off control is managed by turning a stopcock at the top of the condenser (left side of the above diagram). This stopcock is later also used to vent the setup after the solvent is removed.

6. The flask is lowered into the water bath (or the water bath is raised to immerse the flask in the warm water. (On most models, a convenient handle (with height locking mechanism) moves the entire condenser/motor/flask assembly up and down. Often the tilt of the condenser assembly can also be adjusted. The water bath temperature should not exceed the boiling point of the solvent!! For small amounts of common solvents the bath heater is not needed.

7. The solvent should start collecting on the condenser and drip into the receiving flask. Some solvents (such as diethyl ether or dichloromethane) are so volatile that they will also evaporate from the receiving flask and be discharged down the drain. To prevent this, a cooling bath on the receiver or (on some models) use a dry-ice condenser can be used. In addition, an additional trap (with dry-ice or liquid nitrogen) can be placed between the vacuum source and the condenser unit. This is particularly important of a membrane pump is used as vacuum source.

8. Once all the solvent evaporated (or whatever is desired at this point), the vacuum is released, . The flask is raised out of the water bath and the spinning is discontinued. 

9. The bump trap has to be cleaned and the receiving flask is emptied upon completion of the evaporation.


Tips and Tricks

Tips and Tricks

Distilled water should be used in the heating bath to minimize the scale build up in the bath which coats the theoris and heating coils. It is very difficult to remove and reduces the efficiency of the bath. In addition, regular tap water will promote the growth of spectacularly disgusting algae colonies, particularly during the summer months. The best protocol is a regular exchange of the water.

To remove algae gunk from the inside of a coiled water condenser, the condenser has to be removed from the rotavap and the coil is soaked in a dilute nitric acid solution for a few hours. After carefully rinsing the insides, the rotavapor is reassembled. All standard safety precautions should be followed when working with nitric acid!

The ground glass joint holding the flask does not need to be greased, but on rare occasions it (or the bump bulb) may get
1486363922
How to Use Rotary Evaporator or Rotavapor General rules for usage of rotary evaporators 1. The solvent collection flask of the unit should always be emptied prior use to prevent accidentally mixing of incompatible chemicals. SAFETY FIRST! 2. The flask with the solution is placed on the rotary evaporator. The use of a bump trap prevents the solution from accidentally splashing into the condenser (and being contaminated). It is highly advisable to start with a clean bump bulb in case something bumps over after all! This would allow the experimenter to recover the solution or solid. 3. A metal or Keck clip is used to secure the flask and the bump trap. The green one shown below fits 24/40 ground glass joints. Similar blue clips fit 19/22 joints and the yellow ones fit 14/20 joints, which will most likely used in the lab. If you break the bump trap, you will have to pay for it! 4. The dial on the motor is used for speed control of the flask rotation. A typical rotavap uses a variable speed sparkless induction motor that spins at 0-220 rpm and provides high constant torque. A good setting here is 7-8. 5. The aspirator vacuum is turned on. On most models, the vacuum on/off control is managed by turning a stopcock at the top of the condenser (left side of the above diagram). This stopcock is later also used to vent the setup after the solvent is removed. 6. The flask is lowered into the water bath (or the water bath is raised to immerse the flask in the warm water. (On most models, a convenient handle (with height locking mechanism) moves the entire condenser/motor/flask assembly up and down. Often the tilt of the condenser assembly can also be adjusted. The water bath temperature should not exceed the boiling point of the solvent!! For small amounts of common solvents the bath heater is not needed. 7. The solvent should start collecting on the condenser and drip into the receiving flask. Some solvents (such as diethyl ether or dichloromethane) are so volatile that they will also evaporate from the receiving flask and be discharged down the drain. To prevent this, a cooling bath on the receiver or (on some models) use a dry-ice condenser can be used. In addition, an additional trap (with dry-ice or liquid nitrogen) can be placed between the vacuum source and the condenser unit. This is particularly important of a membrane pump is used as vacuum source. 8. Once all the solvent evaporated (or whatever is desired at this point), the vacuum is released, . The flask is raised out of the water bath and the spinning is discontinued. 9. The bump trap has to be cleaned and the receiving flask is emptied upon completion of the evaporation. Tips and Tricks Tips and Tricks Distilled water should be used in the heating bath to minimize the scale build up in the bath which coats the theoris and heating coils. It is very difficult to remove and reduces the efficiency of the bath. In addition, regular tap water will promote the growth of spectacularly disgusting algae colonies, particularly during the summer months. The best protocol is a regular exchange of the water. To remove algae gunk from the inside of a coiled water condenser, the condenser has to be removed from the rotavap and the coil is soaked in a dilute nitric acid solution for a few hours. After carefully rinsing the insides, the rotavapor is reassembled. All standard safety precautions should be followed when working with nitric acid! The ground glass joint holding the flask does not need to be greased, but on rare occasions it (or the bump bulb) may get "frozen". Some companies sell special joint clips that can free frozen joints simply by screwing them in one direction. If you are not lucky enough to have these and cannot release the joint you probably want to ask your teaching assistant for advice. If a mechanical pump is used instead of an aspirator to produce a vacuum, a secondary trap has to be used to prevent that the solvent destroys the membrane or is absorbed in the oil.
SENCO Rotary Evaporators are developed by sticking to the basics, keeping in mind safety of the user and focusing on giving desired results. They enable to achieve desired results affordably for more click on link 
http://kdtraders.com/rotary-evaporator-2-liters/
1517553924
SENCO Rotary Evaporators are developed by sticking to the basics, keeping in mind safety of the user and focusing on giving desired results. They enable to achieve desired results affordably for more click on link http://kdtraders.com/rotary-evaporator-2-liters/
SENCO ROTARY EVAPORATOR  
Another installation 20LTR  ROTARY EVAPORATOR 
#GUJARAT   
SENCO Rotary Evaporators are developed by sticking to the basics, keeping in mind safety of the user and focusing on giving desired results. They enable to achieve desired results affordably and are backed by trustworthy service. The Lab Scale Rotary Evaporator is simple yet accurate, basic yet precise, up to the mark on performance and friendly on budget. Senco rotary evaporator 
We have a unite Senco rotary evaporator in Hyderabad and India we have best price senco rotavapor
1497871024
SENCO ROTARY EVAPORATOR Another installation 20LTR ROTARY EVAPORATOR #GUJARAT SENCO Rotary Evaporators are developed by sticking to the basics, keeping in mind safety of the user and focusing on giving desired results. They enable to achieve desired results affordably and are backed by trustworthy service. The Lab Scale Rotary Evaporator is simple yet accurate, basic yet precise, up to the mark on performance and friendly on budget. Senco rotary evaporator We have a unite Senco rotary evaporator in Hyderabad and India we have best price senco rotavapor
ROTAVAP SENCO ROTARY EVAPORATOR

SENCO Rotary Evaporators are developed by sticking to the basics, keeping in mind safety of the user and focusing on giving desired results. They enable to achieve desired results affordably and are backed by trustworthy service. The Industrial Rotary Evaporator is simple yet accurate, basic yet precise, up to the mark on performance and friendly on budget.

These Rotary Evaporators are used for a variety of applications including:

Concentration
Drying
Refining
Separation
Crystallization
1525768732
ROTAVAP SENCO ROTARY EVAPORATOR SENCO Rotary Evaporators are developed by sticking to the basics, keeping in mind safety of the user and focusing on giving desired results. They enable to achieve desired results affordably and are backed by trustworthy service. The Industrial Rotary Evaporator is simple yet accurate, basic yet precise, up to the mark on performance and friendly on budget. These Rotary Evaporators are used for a variety of applications including: Concentration Drying Refining Separation Crystallization
Rotary Evaporator , one kd chiller for two rotavapor , 
KD CHILLERS , SENCO ROTARY EVAPORATOR , 
 SENCO Rotary Evaporators R206b 2l are developed by sticking to the basics, keeping in mind safety of the user and focusing on giving desired results. They enable to achieve desired results affordably and are backed by trustworthy service. The Lab Scale Rotary Evaporator is simple yet accurate, basic yet precise, up to the mark on performance and friendly on budget. Senco rotary evaporator 
We have a unite Senco rotary evaporator in Hyderabad and India we have best price senco rotavapor
1496644271
Rotary Evaporator , one kd chiller for two rotavapor , KD CHILLERS , SENCO ROTARY EVAPORATOR , SENCO Rotary Evaporators R206b 2l are developed by sticking to the basics, keeping in mind safety of the user and focusing on giving desired results. They enable to achieve desired results affordably and are backed by trustworthy service. The Lab Scale Rotary Evaporator is simple yet accurate, basic yet precise, up to the mark on performance and friendly on budget. Senco rotary evaporator We have a unite Senco rotary evaporator in Hyderabad and India we have best price senco rotavapor

Our timings

[IS_BIZ_OPEN] Mon: 9:00 AM  -  6:00 PM
[IS_BIZ_OPEN] Tue: 9:00 AM  -  6:00 PM
[IS_BIZ_OPEN] Wed: 9:00 AM  -  6:00 PM
[IS_BIZ_OPEN] Thu: 9:00 AM  -  6:00 PM
[IS_BIZ_OPEN] Fri: 9:00 AM  -  6:00 PM
[IS_BIZ_OPEN] Sat: 9:00 AM  -  6:00 PM
[IS_BIZ_OPEN] Sun: Closed  -  Closed

Contact

Kd Traders Furquan Siddique(Proprietor) 10-2-485, Vijay Nagar Colony, Asif Nagar, - 500028, Telangana
+91 8033766128  or   or   
Please keep or 0 before the
number when you dial.
Share Tweet
17.4480788908933 78.4305517232567 KD Traders 9290788196 Kd Traders Furquan Siddique(Proprietor) 10-2-485, Vijay Nagar Colony, Asif Nagar, - 500028, Telangana
False

SUBSCRIBE

5860b1ff68346f1df84141e3KDTRADERSELECTRONICSHYDERABAD57c3c1a65d64370d7cf4eb17